The correct use of ultrasonic clean tooth machine periodontal disease is one of frequently-occurring disease and common disease in oral disease, the incidence of statistics in all countries of the world is higher, teeth cleaning is ideal of periodontal disease treatment, ultrasonic cure unit is a highly efficient clean governance, it is the use of high frequency oscillation energy to remove tartar and plaque, special scale of tooth surface adhesion of soft plaque and pigment is more effective.
The rational use of ultrasonic teeth cleaning machine is very important. Improper operation will cause damage to the tooth and even pulp tissue, and also cause premature wear and power loss of the tool head.
A, action principle of ultrasonic clean tooth machine including two most of the ultrasonic generator and converter, and equipped with mobile phones and can replace the work of the head, and foot switch, its action principle is converts electrical energy into mechanical energy at high frequency, make work head speed vibration, the frequency of 25 KHZ ~ 32 KHZ, the high frequency vibration can make the plaque rupture, and make it fall off from the tooth surface, due to ultrasound
High frequency vibration of the working head produces a lot of heat, so it must be equipped with a cooling system, and the local pressure is generated through the cavitation of water to play the role of cleaning the operation area.
1. Hold the device phone with a modified pen grip, and use it as a conventional fulcrum in the mouth to stabilize the device.
2. Make the long axis of the working head parallel to the long axis of the tooth, the working Angle is not more than 15¡ã, and try to make the working head and the tooth surface fit.
3. Work should not pause on the surface of the teeth, always maintain its movement on the surface of the teeth, vertical alignment of teeth surface can’t work will head end, work head in adjacent surface movement, be careful not to hurt and soft tissue, when work first contact tartar, pressure should be light, using vertical or diagonal movement caused dislocation, plaque such as work head stuck in between teeth, you should immediately stop working.
Then gently exit along the direction of the width gap, can not be forced to twist, more can not maintain the working state, while trying to exit, otherwise it is easy to break the knife head, especially the powerful imported teeth cleaning machine.
4. When the patient is wearing a porcelain crown bridge, the adjacent occlusal surface has fillings, photosensitive resin and other restorations, the working head should not move directly on the crown surface or fillings, so as to avoid crown cracking or filling loss.
5. For subgingival cleaning and treatment, the side of the working tip moves gently along the gingival margin and gradually moves down. The end of the working tip is long and tapering and can be extended into the periodontal pocket.
1. Ultrasonic cleaning appliance has the advantages of high speed, high efficiency, time-saving and labor-saving, constant vibration frequency, high strength, strength, durability, easy to remove calculus, small postoperative reaction, light tooth sensitivity.
2. Water quantity regulation, the working head to water mist as the standard, dripping, indicating that the amount of water is too large, too small will scald the mucous membrane, mouth, teeth, machine damage.
3. Ultrasonic vibration will produce real hole effect, which can more effectively kill anaerobic bacteria in the periodontal pocket.
4. It can meet a variety of clinical needs and is widely used, such as removing crown, removing post nails, and replacing special knife head for root canal treatment.
Four, cleaning and maintenance and disinfection shell, transformer, foot tap wrench, mobile phone line can be wiped with alcohol, non-abrasive neutral clean soft cloth, the working handle can be high temperature and high pressure disinfection, chemical disinfection, the front end of the handle can be unloaded for disinfection.
1. When the handle is connected with the handle line, only gently insert it, do not rotate it.
2. The shape, gloss and surface smoothness of each working tip are of very high standard. Please do not change it by yourself.
3. Tighten and remove the working tip in the direction of the shaft of the handle.
4. In the process of use, when the vibration is weakened, please pay attention to check whether the working tip is tightened.
5. When cleaning, just place the handle gently on the tooth surface. No force is required.
6. Patients with bleeding tendency and placement of pacemaker should not be allowed.
